Difference between revisions of "Group Project ELEPHANT 1.0"

From LVL1
Jump to navigation Jump to search
 
(24 intermediate revisions by one other user not shown)
Line 1: Line 1:
 +
[[File:GP_LVL1_ELEPHANT_PORTRAIT_1_1.jpg]]
  
[[File:GP_LVL1_ELEPHANT_1_0_PINOUT.JPG]]
+
== Information ==
  
[[File:GP_LVL1_ELEPHANT_1_0_WIRING.JPG]]
+
[[File:GP_LVL1_ELEPHANT_1_0_WWW.JPG]]
  
[[File:GP_LVL1_ELEPHANT_1_0_PANEL_LAYOUT.JPG]]
+
== Structure Parts List ==
 +
 
 +
Table Leg
 +
 
 +
Wooden Bowl
 +
 
 +
Broken Wooden Bowl
 +
 
 +
2 U-Bolts and nuts
 +
 
 +
Wooden Panel Board Scrap
 +
 
 +
Chain
  
== Parts List ==
+
== Electronics Parts List ==
  
 
Raspberry PI B
 
Raspberry PI B
Line 36: Line 49:
 
1 Dual 10K Potentiometer (logarithmic)
 
1 Dual 10K Potentiometer (logarithmic)
  
= Old Incomplete and Incorrect Stuff =
+
== Electronics Build ==
  
[[File:GP_LVL1_ELEPHANT_FRITZING.jpg|640px]]
+
[[File:GP_LVL1_ELEPHANT_1_1_PINOUT.JPG]]
  
[[File:GP_LVL1_ELEPHANT_FRITZING_2.jpg]]
+
'''NOTE:''' GPIO conflict between GPIO18 and audio resulted in NEOPIXEL GPIO pin change from GPIO18 to GPIO10.  This change is not reflected in all illustrations and photos.
  
[[File:GP_LVL1_ELEPHANT_FRITZING_3.jpg]]
+
[[File:GP_LVL1_ELEPHANT_1_1_WIRING.JPG]]
  
[[File:GP_LVL1_ELEPHANT_CB_2.jpg]]
+
'''NOTE:''' NEOPIXEL GPIO changed from 18 to 10.  Previous wire X'ed out in RED.
  
== Parts List ==
+
[[File:GP_LVL1_ELEPHANT_1_0_PANEL_LAYOUT.JPG]]
 
 
Raspberry PI B
 
  
4 Relay Module
+
== Actual Photos ==
  
NeoPixel Strip
+
=== Front of Assembly ===
 +
[[File:GP_LVL1_ELEPHANT_PORTRAIT_1_1.jpg]]
  
PIR Motion Sensor
+
=== Eyes and Brow Close Up ===
 +
[[File:GP_LVL1_ELEPHANT_EYES_BROWS_1_1.jpg]]
  
PCA9685 Adafruit's 16-channel 12-bit PWM/Servo Driver
+
=== Rear of Assembly ===
 +
[[File:GP_LVL1_ELEPHANT_HEAD_BACK_2.jpg]]
  
5.5 mm Barrel Jack
+
=== Ear and Servo Linkage ===
 +
[[File:GP_LVL1_ELEPHANT_HEAD_BACK_EAR_LINKAGE_1_1.jpg]]
  
2 Seven Segment Displays
+
=== Inside of Head ===
 +
[[File:GP_LVL1_ELEPHANT_HEAD_BACK_1.jpg]]
  
SPST Switch
+
'''Note:''' Picture prior to eye brow installation.
  
22 Ohm Resistor 1W
+
=== Electronics in Head ===
 +
[[File:GP_LVL1_ELEPHANT_ELECTRONICS_1.jpg]]
  
47 Ohm Resistor 1W
+
=== Control Panel ===
 +
[[File:GP_LVL1_ELEPHANT_CONTROL_PANEL_1.jpg]]
  
1k Ohms Resistor 1/4 W
 
  
10K Resistor 1/4 W
+
== Source Code ==
 +
https://github.com/polewskm/lvl1-elephant

Latest revision as of 22:01, 10 January 2020

GP LVL1 ELEPHANT PORTRAIT 1 1.jpg

Information

GP LVL1 ELEPHANT 1 0 WWW.JPG

Structure Parts List

Table Leg

Wooden Bowl

Broken Wooden Bowl

2 U-Bolts and nuts

Wooden Panel Board Scrap

Chain

Electronics Parts List

Raspberry PI B

4 Relay Module

NeoPixel Strip

PIR Motion Sensor

PCA9685 Adafruit's 16-channel 12-bit PWM/Servo Driver

5.5 mm Barrel Jack

4 LEDs

SPST Switch

100 Ohm Resistor 1W

150 Ohm Resistor 1W

1k Ohms Resistor 1/4 W

10K Resistor 1/4 W

1 Pair USB Powered Speakers

1 Dual 10K Potentiometer (logarithmic)

Electronics Build

GP LVL1 ELEPHANT 1 1 PINOUT.JPG

NOTE: GPIO conflict between GPIO18 and audio resulted in NEOPIXEL GPIO pin change from GPIO18 to GPIO10. This change is not reflected in all illustrations and photos.

GP LVL1 ELEPHANT 1 1 WIRING.JPG

NOTE: NEOPIXEL GPIO changed from 18 to 10. Previous wire X'ed out in RED.

GP LVL1 ELEPHANT 1 0 PANEL LAYOUT.JPG

Actual Photos

Front of Assembly

GP LVL1 ELEPHANT PORTRAIT 1 1.jpg

Eyes and Brow Close Up

GP LVL1 ELEPHANT EYES BROWS 1 1.jpg

Rear of Assembly

GP LVL1 ELEPHANT HEAD BACK 2.jpg

Ear and Servo Linkage

GP LVL1 ELEPHANT HEAD BACK EAR LINKAGE 1 1.jpg

Inside of Head

GP LVL1 ELEPHANT HEAD BACK 1.jpg

Note: Picture prior to eye brow installation.

Electronics in Head

GP LVL1 ELEPHANT ELECTRONICS 1.jpg

Control Panel

GP LVL1 ELEPHANT CONTROL PANEL 1.jpg


Source Code

https://github.com/polewskm/lvl1-elephant