Difference between revisions of "Clive Badger"
Jump to navigation
Jump to search
Line 8: | Line 8: | ||
__NOTOC__ | __NOTOC__ | ||
− | ==ReplicatorG default settings== | + | Note on infill: For models that don't need structural integrity, use less infill. Even in the 2-3% range. Less infill means less wasted plastic. |
+ | |||
+ | Note on slicing profiles: Watch that someone hasn't reset the profile to something experimental that can damage the Makerbot. Stick with Replicator default unless you know what you're doing. | ||
+ | |||
+ | Note on materials: There may be a mixture of ABS and PLA filament. Make sure to check the labeling and your print settings, as the materials require slightly different settings which will effect your printing success. | ||
+ | |||
+ | ==ReplicatorG default ABS settings== | ||
* Slicing Profile: Replicator 2 Default | * Slicing Profile: Replicator 2 Default | ||
* Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck) | * Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck) | ||
Line 20: | Line 26: | ||
* Feedrate (41) | * Feedrate (41) | ||
* Travel Feedrate (51) | * Travel Feedrate (51) | ||
+ | * Print Temperature (220) | ||
+ | |||
+ | ==ReplicatorG Accelerated ABS print settings== | ||
+ | * Slicing Profile: Replicator 2 Default | ||
+ | * Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck) | ||
+ | * Use support Material (Exterior support if you have overhangs greater than 45 degree angles) | ||
+ | * Use default start / end gcode (Always check) | ||
+ | * Use Print-O-Matic (Always check) | ||
+ | ===Settings=== | ||
+ | * Object Infill (10%) | ||
+ | * Layer Height (.27) | ||
+ | * Number of Shells (1) | ||
+ | * Feedrate (80) | ||
+ | * Travel Feedrate (150) | ||
+ | * Print Temperature (230) | ||
+ | |||
+ | ==ReplicatorG fine resolution ABS print settings== | ||
+ | * Slicing Profile: Replicator 2 Default | ||
+ | * Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck) | ||
+ | * Use support Material (Exterior support if you have overhangs greater than 45 degree angles) | ||
+ | * Use default start / end gcode (Always check) | ||
+ | * Use Print-O-Matic (Always check) | ||
+ | ===Settings=== | ||
+ | * Object Infill (10%) | ||
+ | * Layer Height (.2) | ||
+ | * Number of Shells (1) | ||
+ | * Feedrate (40) | ||
+ | * Travel Feedrate (50) | ||
* Print Temperature (220) | * Print Temperature (220) | ||
Purchased for LVL1 from NSF funds for the UofL Speed School Co-op Makership | Purchased for LVL1 from NSF funds for the UofL Speed School Co-op Makership |
Revision as of 10:38, 10 December 2012
[Equipment|Back to list of Equipment]]
General
|
Note on infill: For models that don't need structural integrity, use less infill. Even in the 2-3% range. Less infill means less wasted plastic.
Note on slicing profiles: Watch that someone hasn't reset the profile to something experimental that can damage the Makerbot. Stick with Replicator default unless you know what you're doing.
Note on materials: There may be a mixture of ABS and PLA filament. Make sure to check the labeling and your print settings, as the materials require slightly different settings which will effect your printing success.
ReplicatorG default ABS settings
- Slicing Profile: Replicator 2 Default
- Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck)
- Use support Material (Exterior support if you have overhangs greater than 45 degree angles)
- Use default start / end gcode (Always check)
- Use Print-O-Matic (Always check)
Settings
- Object Infill (10%)
- Layer Height (.27)
- Number of Shells (1)
- Feedrate (41)
- Travel Feedrate (51)
- Print Temperature (220)
ReplicatorG Accelerated ABS print settings
- Slicing Profile: Replicator 2 Default
- Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck)
- Use support Material (Exterior support if you have overhangs greater than 45 degree angles)
- Use default start / end gcode (Always check)
- Use Print-O-Matic (Always check)
Settings
- Object Infill (10%)
- Layer Height (.27)
- Number of Shells (1)
- Feedrate (80)
- Travel Feedrate (150)
- Print Temperature (230)
ReplicatorG fine resolution ABS print settings
- Slicing Profile: Replicator 2 Default
- Use Raft / Support (Check if you have overhangs or many pieces on a single build, otherwise uncheck)
- Use support Material (Exterior support if you have overhangs greater than 45 degree angles)
- Use default start / end gcode (Always check)
- Use Print-O-Matic (Always check)
Settings
- Object Infill (10%)
- Layer Height (.2)
- Number of Shells (1)
- Feedrate (40)
- Travel Feedrate (50)
- Print Temperature (220)
Purchased for LVL1 from NSF funds for the UofL Speed School Co-op Makership