Part Selection

Parts
Name	Image	Details	Considerations
Small Wooden Coffin		Small Body Storage Cheap and Wooden	Just another item to put me on a watch list
ArduCam ESP32S Uno w/ PSRAM		OV2640 Camera ESP32S WiFi BLE SD MMC	Based on AI-Thinker ESP32 Camera Configuration and hardware setup Discontinued hardware, so time to use.
SFX Halloween Module		Sound and LED Sequences Strobe Function Sound/Vibration Activation Demo Button	Prebuilt Unit Already themed for coffin themed project
Round Display		1.28 inch LCD Module 240 x 204 Pixels GCA901A Controller	Realistic Corpse Viewing Port
SD Card Adapter		Micro SD Storage Board SPI Interface
Battery Holders		1 AAA Cell 2 AAA Cells	Volume Issues lead to use of two holders instead of a single 3 AAA cell holder 2 AA Holder used was not messed up like the one in this photo.
ICR18650 Battery		2200mAh 3.7V	Had one lying around
PC817 Optocoupler

Element Preparation

Elements
Halloween SFX Module	ArduCam ESP32S Uno w/ PSRAM	Coffin Top	Coffin Bottom
Front Shell – (Not Used) Reflector – (Not Used) High Brightness LED 2x4 Matrix Circuit Board Assembly PCB Function Switch – (Removed) Strobe Speed Potentiometer – (Removed) Speaker Piezo Disk – (Not Used) Demo Button – (Not Used) Back Shell with integrated Battery Holder – (Not Used) Battery Cover – (Not Used)	Right Angle Inward Facing Male Header Pins on Underside Spacers Mounted on USB End of Board	1.25" Upper End Hole for Round Display View 3/8" Lower Mid Section Hole for Camera View Port Inside Inner Edge Carve Outs for ArduCam Board Mounting Inside Bottom Edge Carve Out for Custom Bus Board Mounting	Micro USB Access Slot in Bottom End Two Small Holes for Micro USB Socket Adapter Mounting

GPIO02 boot-up tests for PSRAM voltage requirement interfered with HSPI Bus usage. Requires eFuse setting to voltage PSRAM voltage level for HSPI normal operation
ESP32 Cam with AI-Thinker hardware setup can be used for the project with a simple pin assignment change.
An overly elaborate method for using a vibrating motor to trigger SFX module, isolating the module electrically from Microcontroller abandon due to unnecessary complexity and stray triggering from handling project.
SFX module uses High Brightness LEDs that cause short bursts of high current that have to be handles by separate battery pack in order to not require additional power supply circuitry for a common power supply.
I had a ICR18650 lying around, so battery operation of project utilizing built in charging of the ArduCam. Then again, it could be a self-destruct method.

Parts
Item	Link
ArduCam Product Page	https://www.arducam.com/product/b0192-arducam-iotai-esp32-uno-psram-ov2640-camera/
GCA901A Demo on ESP32	https://github.com/talofer99/ESP32CAM-Capture-and-send-image-over-esp-now
ESP32 SPI Information	https://randomnerdtutorials.com/esp32-spi-communication-arduino/
ESP32 Now	https://randomnerdtutorials.com/esp-now-two-way-communication-esp32/
ESP32 Cam Photo Webserver	https://randomnerdtutorials.com/esp32-cam-take-photo-display-web-server/
ESP32 Cam Selfie	https://robotzero.one/esp32-cam-tft-selfie/
ESP32 Cam Pinout Guide	https://randomnerdtutorials.com/esp32-cam-ai-thinker-pinout/
ESP32 Cam Settings Guide	https://randomnerdtutorials.com/esp32-cam-ov2640-camera-settings/
ESP32 Cam as Camera with Display	https://www.instructables.com/ESP32-ESP32-CAM-With-OV2640-Using-SIPHSPI-for-TFT-/
ESP32 Camera and Webserver Sample Program from hardware library	Ardunio IDE Library
ESP-DL	https://github.com/espressif/esp-dl