Pseudo Medical Monitor Device 3D Print: Difference between revisions
Jump to navigation
Jump to search
| Line 50: | Line 50: | ||
[[File:JAC MED MON RESP MODEL RENDER.jpg|left|thumbnail|x200px]] | [[File:JAC MED MON RESP MODEL RENDER.jpg|left|thumbnail|x200px]] | ||
| | | | ||
Two Compression Brackets | |||
Compression Sensor Inside | |||
|- | |- | ||
[[File:JAC MED MON RESP MODEL 1 RENDER A.jpg|left|thumbnail|x200px]] | [[File:JAC MED MON RESP MODEL 1 RENDER A.jpg|left|thumbnail|x200px]] | ||
| | | | ||
* BLUE - Compression Sensor Orientation Stabilizer | * BLUE - Compression Sensor Orientation Stabilizer | ||
* YELLOW - Compression Sensor Lower Bracket | * YELLOW - Compression Sensor Lower Bracket | ||
* GREEN - Compression Sensor Top Bracket | * GREEN - Compression Sensor Top Bracket | ||
* CYAN - Telescoping Tube Cradle | * CYAN - Telescoping Tube Cradle | ||
* RED - Rubber Band (Provides Flexing of Compression Sensor Brackets) | * RED - Rubber Band (Provides Flexing of Compression Sensor Brackets) | ||
* VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move) | * VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move) | ||
* SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible) | * SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible) | ||
|} | |} | ||
Revision as of 16:34, 9 December 2021
Printed Parts
| 3D Printed Parts | ||
|---|---|---|
| Parts | ID | Purpose |
 |
Control Panel Brackets |
Fasten Control Panel to Main Device Sensor Layer Brackets are not symmetrical and are tailored for the Main Device Sensor Layer hole placement Screws shown with nuts provide offset positioning |
 |
Port Mounting Brackets |
Secure RJ45 Ports to Arduino DUE base layer of Main Device Brackets are not symmetrical and are tailored for the Arduino DUE hole placement Velco added post printing |
 |
ATTiny85 Token Enclosure Box and Cover | Provides an enclosure for ATTiny85 Tokens |
 |
Corner Bracket Set |
Provides corner bracketing for EEG External Unit Threaded Inserts installed after printing |
 |
Respiratory Sensor Signal Amplifier Box and Cover |
Provides enclosure of PCB Access to adjustment potentiometer from cover |
Assemblies With Printed Parts
Respiratory Sensor used with EKG External Unit
| 3D Printed Parts | |
|---|---|
 |
Two Compression Brackets Compression Sensor Inside |
* BLUE - Compression Sensor Orientation Stabilizer * YELLOW - Compression Sensor Lower Bracket * GREEN - Compression Sensor Top Bracket * CYAN - Telescoping Tube Cradle * RED - Rubber Band (Provides Flexing of Compression Sensor Brackets) * VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move) * SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible) | |
Respiratory Sensor used with Poly-Liar External Unit
- YELLOW - Telescoping Tube Cradle
- GREEN - Sliding Plunger
- RED - Rubber Band (Provides Resistance and Recoil for Sliding Plunger against Telescoping Cradle)
- VIOLET - Reflectance Sensor PCB
- BLUE - Fastner (Secures Slinging Plunger to Inner Telescoping Tube)
- ORANGE - Inner Telescoping Tube
- SEMI-TRANSPARENT BLUE - Guide Tube for Sliding Plunger
- SEMI-TRANSPARENT GREEN - Outer Telescoping Tube
