LazerTazerTag: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| (4 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
* Setup Game Sketch in Arduino | * Setup Game Sketch in Arduino | ||
* Would be nice to figure out how to use a small chip to just out a specific IR code over and over | * Would be nice to figure out how to use a small chip to just out a specific IR code over and over | ||
== Task To Do == | == Task To Do == | ||
| Line 20: | Line 21: | ||
* Possibly More Tense Units | * Possibly More Tense Units | ||
* IR Domes and PCB's | * IR Domes and PCB's | ||
* Possibly Two more Rifles | *<strike> Possibly Two more Rifles</strike> | ||
*<strike> 16 Tens Unit Lead Wire Sets</strike> | |||
* LOTS OF BATTERIES | * LOTS OF BATTERIES | ||
* Two more packs of elastic for arm/leg bands | * Two more packs of elastic for arm/leg bands | ||
| Line 26: | Line 28: | ||
* Knee Pads | * Knee Pads | ||
* Elbow Pads | * Elbow Pads | ||
== Arduino GamePlay == | == Arduino GamePlay == | ||
| Line 37: | Line 38: | ||
* Start Game | * Start Game | ||
* IR In is on interrupt | * IR In is on interrupt | ||
| Line 44: | Line 44: | ||
* IR Med Packs | * IR Med Packs | ||
* IR Granades | * IR Granades | ||
== Build Instructions for Full Set == | |||
=== Gun Wiring === | |||
Gun wiring taps inside gun and comes out through headphone port. Terminate each end with a JST plug and label as 1,2,3. | |||
* IR Receiver | |||
* 5V | |||
* Gnd | |||
* On/Off Toggle | |||
* LifeLED1 | |||
* LifeLED2 | |||
* LifeLED3 | |||
* TeamSelect | |||
* IR Out | |||
=== IR Domes === | |||
IR Domes get wired to a JST plug | |||
* IR Recieve | |||
* Pwr | |||
* Gnd | |||
=== Tense Leads === | |||
Tens leads are left as Raw leads and ran through the shoulder and belt loops to the inside of the vest pocket. | |||
* GND lead of each tense set goes to common groun | |||
* V+ of each lead gets ran through 5V relay channel | |||
Latest revision as of 13:35, 23 July 2012
Still To Figure Out
- Sending Medic IR from arduino
- SpreadSheet of all IR Codes [1]
- Reading IR pin on Arduino
- SpreadSheet of all IR Codes [2]
- Setup Game Sketch in Arduino
- Would be nice to figure out how to use a small chip to just out a specific IR code over and over
Task To Do
- Build Cardboard Forts and Barriers
- Make additional 360 IR Domes
- Make 2 more full arm/leg band sets
- Move guns On/Off switch to arduino pin
- Move guns "Team Select button to Arduino Pin
- Add 2 Arduino ON/Off Push Buttons for gameplay options
Need To Purchase or Acquire
- More IR Receivers
- Possibly More Tense Units
- IR Domes and PCB's
Possibly Two more Rifles16 Tens Unit Lead Wire Sets- LOTS OF BATTERIES
- Two more packs of elastic for arm/leg bands
- Facemask
- Knee Pads
- Elbow Pads
Arduino GamePlay
The arduino will control the on/off of the gun. Game Play order:
- Gun On
- Finger Print on Rifles
- Set Team
- Check for Three Solid Life bars
- Start Game
- IR In is on interrupt
If we have time
- IR Blaster on Parrot AR Drone
- IR Med Packs
- IR Granades
Build Instructions for Full Set
Gun Wiring
Gun wiring taps inside gun and comes out through headphone port. Terminate each end with a JST plug and label as 1,2,3.
- IR Receiver
- 5V
- Gnd
- On/Off Toggle
- LifeLED1
- LifeLED2
- LifeLED3
- TeamSelect
- IR Out
IR Domes
IR Domes get wired to a JST plug
- IR Recieve
- Pwr
- Gnd
Tense Leads
Tens leads are left as Raw leads and ran through the shoulder and belt loops to the inside of the vest pocket.
- GND lead of each tense set goes to common groun
- V+ of each lead gets ran through 5V relay channel