Difference between revisions of "Pseudo Medical Monitor Device 3D Print"
Jump to navigation
Jump to search
| Line 50: | Line 50: | ||
[[File:JAC MED MON RESP MODEL RENDER.jpg|left|thumbnail|x200px]] | [[File:JAC MED MON RESP MODEL RENDER.jpg|left|thumbnail|x200px]] | ||
| | | | ||
| + | Two Compression Brackets | ||
| + | Compression Sensor Inside | ||
|- | |- | ||
[[File:JAC MED MON RESP MODEL 1 RENDER A.jpg|left|thumbnail|x200px]] | [[File:JAC MED MON RESP MODEL 1 RENDER A.jpg|left|thumbnail|x200px]] | ||
| | | | ||
| − | * BLUE - Compression Sensor Orientation Stabilizer | + | * BLUE - Compression Sensor Orientation Stabilizer |
| − | * YELLOW - Compression Sensor Lower Bracket | + | * YELLOW - Compression Sensor Lower Bracket |
| − | * GREEN - Compression Sensor Top Bracket | + | * GREEN - Compression Sensor Top Bracket |
| − | * CYAN - Telescoping Tube Cradle | + | * CYAN - Telescoping Tube Cradle |
| − | * RED - Rubber Band (Provides Flexing of Compression Sensor Brackets) | + | * RED - Rubber Band (Provides Flexing of Compression Sensor Brackets) |
| − | * VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move) | + | * VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move) |
| − | * SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible) | + | * SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible) |
|} | |} | ||
Revision as of 16:34, 9 December 2021
Contents
Printed Parts
| 3D Printed Parts | ||
|---|---|---|
| Parts | ID | Purpose |
| Control Panel Brackets |
Fasten Control Panel to Main Device Sensor Layer Brackets are not symmetrical and are tailored for the Main Device Sensor Layer hole placement Screws shown with nuts provide offset positioning | |
| Port Mounting Brackets |
Secure RJ45 Ports to Arduino DUE base layer of Main Device Brackets are not symmetrical and are tailored for the Arduino DUE hole placement Velco added post printing | |
| ATTiny85 Token Enclosure Box and Cover | Provides an enclosure for ATTiny85 Tokens | |
| Corner Bracket Set |
Provides corner bracketing for EEG External Unit Threaded Inserts installed after printing | |
| Respiratory Sensor Signal Amplifier Box and Cover |
Provides enclosure of PCB Access to adjustment potentiometer from cover | |
Assemblies With Printed Parts
Respiratory Sensor used with EKG External Unit
| 3D Printed Parts | |
|---|---|
Two Compression Brackets Compression Sensor Inside | |
* BLUE - Compression Sensor Orientation Stabilizer * YELLOW - Compression Sensor Lower Bracket * GREEN - Compression Sensor Top Bracket * CYAN - Telescoping Tube Cradle * RED - Rubber Band (Provides Flexing of Compression Sensor Brackets) * VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move) * SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible) | |
Respiratory Sensor used with Poly-Liar External Unit
- YELLOW - Telescoping Tube Cradle
- GREEN - Sliding Plunger
- RED - Rubber Band (Provides Resistance and Recoil for Sliding Plunger against Telescoping Cradle)
- VIOLET - Reflectance Sensor PCB
- BLUE - Fastner (Secures Slinging Plunger to Inner Telescoping Tube)
- ORANGE - Inner Telescoping Tube
- SEMI-TRANSPARENT BLUE - Guide Tube for Sliding Plunger
- SEMI-TRANSPARENT GREEN - Outer Telescoping Tube
