View source for Pseudo Medical Monitor Device 3D Print


= Printed Parts =

{|class="wikitable"
!colspan="3"|3D Printed Parts
|-
| Parts
| ID
| Purpose
|-
|[[File:JAC_MED_MON_CONTROL_PANEL_BRACKETS.jpg|left|thumbnail|x200px]]
| Control Panel Brackets
| 
 Fasten Control Panel to Main Device Sensor Layer 
 Brackets are not symmetrical and are tailored for the Main Device Sensor Layer hole placement
 Screws shown with nuts provide offset positioning
|-
|[[File:JAC_MED_MON_PORT_MOUNTING_BRACKETS.jpg|left|thumbnail|x200px]]
| Port Mounting Brackets
| 
 Secure RJ45 Ports to Arduino DUE base layer of Main Device
 Brackets are not symmetrical and are tailored for the Arduino DUE hole placement
 Velco added post printing 
|-
|[[File:JAC MED MON ATTINY85 TOKEN BOX PARTS.jpg|left|thumbnail|x200px]]
| ATTiny85 Token Enclosure Box and Cover
| Provides an enclosure for ATTiny85 Tokens
|-
|[[File:JAC MED MON EEG BOX BRACKETS.jpg|left|thumbnail|x200px]]
| Corner Bracket Set
| 
 Provides corner bracketing for EEG External Unit
 Threaded Inserts installed after printing
|-
|[[File:JAC MED MON RESPIRATORY SENSOR BOX.jpg|left|thumbnail|x200px]]
| Respiratory Sensor Signal Amplifier Box and Cover
| 
 Provides enclosure of PCB
 Access to adjustment potentiometer from cover
|-
|
[[File:JAC_MED_MON_RESPIRATORY_SENSOR_A_COMPRESSION_BRACKET.jpg|left|thumbnail|x200px]]
| Respiratory Sensor A Compression Bracket
|
 Encase IR Distance Compression Sensor
|-
|
[[File:JAC_MED_MON_RESPIRATORY_SENSOR_A_STABLIZING_BASE.jpg|left|thumbnail|x200px]]
| Respiratory Sensor A Orientation Stabilizer
|
Keep compression sensor oriented 
|-
|
[[File:JAC_MED_MON_RESPIRATORY_SENSOR_A_CRADLE.jpg|left|thumbnail|x200px]]
| Respiratory Sensor A Cradle
|
Secure Telescoping Tube to sensor 
|-
|
[[File:JAC_MED_MON_RESPIRATORY_SENSOR_B_PLUNGER.jpg|left|thumbnail|x200px]]
| Respiratory Sensor B Sliding Plunger
|
Proximity surface for IR reflectance Sensor
|-
|
[[File:JAC_MED_MON_RESPIRATORY_SENSOR_B_CRADLE.jpg|left|thumbnail|x200px]]
| Respiratory Sensor B Cradle
|
Secure Telescoping Tube to sensor
|-
|
[[File:JAC MED MON EKG SIGNAL BOX.jpg|left|thumbnail|x200px]]
| Signal Box
|Amplify Breathing Sensor Type A Signal
|}

= Assemblies With Printed Parts =

== Respiratory Sensor used with EKG External Unit ==

{|class="wikitable"
!colspan="2"| Renders
|-
|
[[File:JAC MED MON RESP MODEL RENDER.jpg|left|thumbnail|x200px]]
|
* Two Compression Brackets 
* IR Distance Compression Sensor Inside
|-
|
[[File:JAC MED MON RESP MODEL 1 RENDER A.jpg|left|thumbnail|x200px]]
|
* BLUE - Compression Sensor Orientation Stabilizer
* YELLOW - Compression Sensor Bracket Oriented as Lower
* GREEN - Compression Sensor Bracket Oriented as Upper
* CYAN - Telescoping Tube Cradle
* RED - Rubber Band (Provides Flexing of Compression Sensor Brackets)
* VIOLET - Fastner (Holds Exterior Telescoping Tube Secure and Allows Inner Tube to Move)
* SEMI-TRANSPARENT GREEN - Outer Telescoping Tube (Inner Telescoping Tube visible)
|}

== Respiratory Sensor used with Poly-Liar External Unit ==

{|class="wikitable"
!colspan="2"|Renders
|-
|
[[File:JAC MED MON RESP MODEL 2 RENDER C.jpg|left|thumbnail|x200px]]
|
* YELLOW - Telescoping Tube Cradle
* GREEN - Sliding Plunger
* RED - Rubber Band (Provides Resistance and Recoil for Sliding Plunger against Telescoping Cradle)
* VIOLET - Reflectance Sensor PCB
* BLUE - Fastner (Secures Slinging Plunger to Inner Telescoping Tube)
* ORANGE - Inner Telescoping Tube
* SEMI-TRANSPARENT BLUE - Guide Tube for Sliding Plunger
* SEMI-TRANSPARENT GREEN - Outer Telescoping Tube
|-
|
[[File:JAC MED MON RESP MODEL 2 RENDER B.jpg|left|thumbnail|x200px]]
|
* YELLOW - Telescoping Tube Cradle
* GREEN - Sliding Plunger
* RED - Rubber Band (Provides Resistance and Recoil for Sliding Plunger against Telescoping Cradle)
* BLUE - Fastner (Secures Slinging Plunger to Inner Telescoping Tube)
* ORANGE - Inner Telescoping Tube
* SEMI-TRANSPARENT GREEN - Outer Telescoping Tube
|}

[[Pseudo-Medical Monitor Device Design]]

[[Pseudo-Medical Monitor]]