Difference between revisions of "5th Inning"

From LVL1
Jump to navigation Jump to search
Line 28: Line 28:
 
==Code==
 
==Code==
 
Cut and paste into your Arduino code environment.  This code will light the LED connected to pin 2 when the button is pushed.  If you removed the led from Inning 2, do not worry, pin 13 has a soldered on LED on most Arduinos and clones.  Pin 2 was used, so the switch does not have to be removed for future experiments.
 
Cut and paste into your Arduino code environment.  This code will light the LED connected to pin 2 when the button is pushed.  If you removed the led from Inning 2, do not worry, pin 13 has a soldered on LED on most Arduinos and clones.  Pin 2 was used, so the switch does not have to be removed for future experiments.
 +
 +
NOTE: The circuit and code on the Arduino site really does not work very well.  In the case of just turning on and off a led, it works ok, but having a floating low when the switch is pushed makes the circuit unreliable.  To fix (Thanks Tim Knowles) we have the circuit default to low, then we pull the line high when the switch is pushed by engaging the internal resistor using this line of code...
 +
<pre>
 +
digitalWrite(inPin,HIGH);  //engages internal pullup resistor
 +
</pre>
 +
really it works!  Try it!
  
 
<pre>
 
<pre>
Line 52: Line 58:
 
   pinMode(ledPin, OUTPUT);  // declare LED as output
 
   pinMode(ledPin, OUTPUT);  // declare LED as output
 
   pinMode(inPin, INPUT);    // declare pushbutton as input
 
   pinMode(inPin, INPUT);    // declare pushbutton as input
 +
  digitalWrite(inPin,HIGH);  //engages internal pullup resistor
 
}
 
}
  

Revision as of 14:37, 19 May 2010

Introduction

Pushbutton Switches Switches are probably the most common human to computer input. Fortunatly they are easy to do. This circuit uses a pull-up resistor and a pushbutton switch to light an LED.

Components Needed

  • Freeduino or Arduino or clone
  • USB cable for Freeduino
  • Freeduino development software - download here!
  • Solderless Breadboard
  • Hookup wire 22gauge solid
  • Pushbutton Switch
  • Soldering Iron and Solder to solder wires to switch
  • 1 kOhm resistor (Brown-Black-Red)

How to

  1. For our workshop, you will have to solder some hookup wire to one of your pushbutton switches. Just strip back a half an inch of wire or so, stick it through the hole on the switch lead and solder. You will have help. It is easy.
  2. Follow the fritzing diagram and hook up the circuit.
  3. Cut and paste your code and run!

Schematic

Lvl1-Inning5 schem.jpg

Fritzing

Lvl1-Inning5 bb.jpg

Code

Cut and paste into your Arduino code environment. This code will light the LED connected to pin 2 when the button is pushed. If you removed the led from Inning 2, do not worry, pin 13 has a soldered on LED on most Arduinos and clones. Pin 2 was used, so the switch does not have to be removed for future experiments.

NOTE: The circuit and code on the Arduino site really does not work very well. In the case of just turning on and off a led, it works ok, but having a floating low when the switch is pushed makes the circuit unreliable. To fix (Thanks Tim Knowles) we have the circuit default to low, then we pull the line high when the switch is pushed by engaging the internal resistor using this line of code...

digitalWrite(inPin,HIGH);  //engages internal pullup resistor

really it works! Try it!

 
/* Basic Digital Read
 * ------------------ 
 *
 * turns on and off a light emitting diode(LED) connected to digital  
 * pin 13, when pressing a pushbutton attached to pin 2. It illustrates the
 * concept of Active-Low, which consists in connecting buttons using a
 * 1K to 10K pull-up resistor.
 *
 * Created 1 December 2005
 * copyleft 2005 DojoDave <http://www.0j0.org>
 * http://arduino.berlios.de
 *
 */

int ledPin = 13; // choose the pin for the LED
int inPin = 2;   // choose the input pin (for a pushbutton)
int val = 0;     // variable for reading the pin status

void setup() {
  pinMode(ledPin, OUTPUT);  // declare LED as output
  pinMode(inPin, INPUT);    // declare pushbutton as input
  digitalWrite(inPin,HIGH);  //engages internal pullup resistor
}

void loop(){
  val = digitalRead(inPin);  // read input value
  if (val == HIGH) {         // check if the input is HIGH (button released)
    digitalWrite(ledPin, LOW);  // turn LED OFF
  } else {
    digitalWrite(ledPin, HIGH);  // turn LED ON
  }
}


Run this code instead if you have the LCD hooked up. It says whether the button is up or down on the neato display!

//This switch code looks at the pushbutton pin (2)
//and resets the counter if it is pressed!
//bpw 5/11/10


// include the library code:
#include <LiquidCrystal.h>

// initialize the library with the numbers of the interface pins
LiquidCrystal lcd(7, 8, 9, 10, 11, 12);

int inPin = 2;   // choose the input pin (for a pushbutton)
int val = 0;     // variable for reading the pin status



void setup() {
  // set up the LCD's number of rows and columns: 
  lcd.begin(16, 2);
  // Print a message to the LCD.
  lcd.print("hello, world!");
  
  pinMode(inPin, INPUT);    // declare pushbutton as input
digitalWrite(inPin,HIGH);  //engages internal pullup resistor
}

void loop() {
  // set the cursor to column 0, line 1
  // (note: line 1 is the second row, since counting begins with 0):
  lcd.setCursor(0, 1);
  // print the number of seconds since reset:
  lcd.print(millis()/1000);
  
  lcd.setCursor(8, 1);  //col 8, row 1
  //code for button pressed!
  val = digitalRead(inPin);  // read input value
  if (val == LOW) {         // check if the input is HIGH (button released)
    lcd.print("DOWN");
  } else {
    lcd.print("UP  ");
  }

}



Troubleshooting

Resources

See http://www.arduino.cc/en/Tutorial/Pushbutton for more information on pushbutton switches.

Here is the link to the LCD Library http://arduino.cc/en/Reference/LiquidCrystal?from=Tutorial.LCDLibrary